Rod Mills

Attention: Operators

It is imperative to use the utmost care to avoid contact with the moving parts of the machine in operation. There is no need to touch anything while it performs the intended function.

Any alterations, re-wiring or modifications to be done on this machine while under warranty, must be authorized by the manufacturer otherwise all warranties become void.
Rod/Ball Mill 13 x 22 Operating Manual
WARNING! Do not start the motor with a safety enclosure retracted and doors open. For emptying and recharging the milling chamber, turn off the electric drive, open the doors and retract the safety enclosure.

https://www.911metallurgist.com/equipment/grinding-mills/

Manually rotate the mill’s yoke in the horizontal position. Lock the milling chamber by engaging the Locking Bar, part 44. Loosen the mill’s locking T-screw in the yoke’s side and let it swing vertically. Remove the lid and rotate the milling chamber upside down to remove the ground media. Reverse the operations once the milling chamber is refilled with new media.

Warning: Remember to retract the Locking Bar, part 44 before closing the doors and starting the motor. Failure to retract the Locking Bar will cause damage to the machine and/or serious injury.

Grinding Chamber Rotation:

Note that the grinding chamber must always rotate counterclockwise to prevent any loosening of fasteners. To check the chambers direction of rotation, run it at the maximum rpm setting while empty, then open the door quickly to check the rotation direction.
Operational Instructions
Procedure for loading samples and grinding media:

Open both front doors and slide main door all the way back.

Rotate grinding chamber (RBM005-1322) by hand to locking position. Pull and rotate locking bar (RBM044) 90 degrees and release slowly into the locating hole, making sure that the tapered end of the locking bar has fully entered the hole. If necessary you may have to jog the chamber by hand to ensure the locking bar is fully engaged.

Remove the locking handle (RBM015) by turning counter clockwise.

Tilt the grinding chamber so that the lid is facing upwards.

Turn the screw handle (RBM009) counterclockwise on the yoke (RBM008-1322) until the yoke is loose enough to slide left or right and be removed.
Remove the lid (RBM007-1322) and place grinding charge (balls/rods) in the chamber. The charge should occupy approximately 40-45% of the chamber.

Place the sample material inside the grinding chamber. The chamber should be approximately 50-60% full with the charge and the sample material loaded.

Place the lid back on the chamber.
Slide the yoke (RBM008-1322) back in place and retighten it with the screw handle (RBM009).
Tilt the grinding chamber so the lid is facing forwards and screw the locking handle (RBM015) back in by turning it clockwise.
Pull and rotate locking bar (RBM044) 90 degrees and release it slowly into the unlocked position so the chamber can rotate freely.

Slide the main door all the way forward and make sure that both front doors are latched closed.
Set the timer on the control panel and press start to begin grinding operation.

Procedure for unloading samples and grinding media:

Open both front doors and slide main door all the way back.

Rotate grinding chamber by hand (RBM005-1322) to locking position. Pull and rotate locking bar (RBM044) 90 degrees and release slowly into the locating hole, making sure that the tapered end of the locking bar has fully entered the hole. If necessary you may have to jog the chamber by hand to ensure the locking bar is fully engaged.

Remove the locking handle (RBM015) by turning counterclockwise.

Tilt the milling chamber so that the lid is facing upwards.

Turn the screw handle (RBM009) counterclockwise on the yoke (RBM008-1322) until the yoke is loose enough to slide left or right and be removed.

Remove the lid (RBM007-1322) and remove all milling media (balls/rods) from the chamber.
Set your collection container/bucket beneath the chamber.

Grab the handle on the back of the milling chamber and tilt it forward to pour out the sample.

13 x 22 Rod Mill Parts List
RBM001……………………………………………………..Frame
RBM002A-1………………………………………….Rear side panel (Right)
RBM002B-1………………………………………….Rear Side panel (left)
RBM003-1………………………………………….Front side panel (2pcs)
RBM004-1………………………………………….Rear Panel
RBM005-1322………………………………………….Grinding Chamber
RBM006………………………………………….Yoke
RBM007-1322………………………………………….Lid for Chamber
RBM008-1322………………………………………….Chamber yoke
RBM009………………………………………….Screw Handle
RBM010………………………………………….Sleeve (2pcs)
RBM011………………………………………….Rigid Caster (2pcs)
RBM012-2………………………………………….Washer (2pcs)
RBM013-2………………………………………….Nut (2pcs)
RBM014-12………………………………………….Set screw (2pcs)
RBM015………………………………………….Locking Handle
RBM016………………………………………….Shaft
RBM017………………………………………….Pillow block bearing (larger)
RBM017A-1………………………………………….Pillow block mounting hardware
RBM017A-2………………………………………….Pillow block mounting hardware
RBM018………………………………………….Spacer
RBM018-1………………………………………….Spacer (Taller)
RBM019………………………………………….Pillow block bearing (smaller)
RBM021A………………………………………….Coupling half (2pcs)
RBM021B………………………………………….Coupling Insert
RBM022-1………………………………………….Reducer
RBM024-1………………………………………….Motor
RBM025-2………………………………………….Motor Cover
RBM026-3………………………………………….Sliding Door
RBM027-3………………………………………….Right door
RBM028-3………………………………………….Left door
RBM028A………………………………………….Hinge screw (22pcs)
RBM030………………………………………….O-ring for Chamber
RBM033………………………………………….Key (Larger)
RBM033B………………………………………….Key (on gearbox shaft)
RBM034-2………………………………………….Front panel
RBM039-2………………………………………….Side rail
RBM041………………………………………….Key (Smaller)
RBM041A………………………………………….Key (Larger)
RBM041B………………………………………….Set screw (longer)
RBM041C………………………………………….Set Screw (shorter)
RBM042………………………………………….Spring
RBM043………………………………………….pin (2pcs)
RBM043A………………………………………….Washer
RBM044………………………………………….Locking Handle
RBM045-1………………………………………….Screw
RBM045D-1………………………………………….Heavy Washer
RBM046-1………………………………………….Locking Bracket
RBM047-1………………………………………….Yoke Screw
RBM047C………………………………………….Lockwasher
RBM047D………………………………………….Washer
RBM048-2………………………………………….Nylock Nut (2pcs)
RBM050-2………………………………………….Locking Plate
RBM053-2………………………………………….Deflector Plate
RBM054………………………………………….Roller (4pcs)
RBM054E………………………………………….Roller Holding Screw (back wheels) – 4pcs
RBM054F-1………………………………………….Roller Holding Insert (back wheels) – 4pcs
RBM054G………………………………………….Nut (4pcs)
RBM055-1………………………………………….Slide block (4pcs)
RBM055B………………………………………….Slide block screw (8pcs)
RBM070………………………………………….Magnet (2pcs)
RBM070A………………………………………….Screw for magnet (2pcs)
RBM071-1………………………………………….Magnet holding block (2pcs)
RBM073………………………………………….Screw (2pcs)
RBM073A………………………………………….Lockwasher (2pcs)
RBM074………………………………………….Switch Mounting plate (2pcs)
RBM074A………………………………………….Hardware (2 sets)
RBM075………………………………………….Door Switch (2pcs)
RBM075A………………………………………….Door Switch Hardware (2 sets)
RBM075B………………………………………….Switch Spacer (2pcs)
RBM075C………………………………………….Lock washer
RBM075D………………………………………….Washer
RBM076………………………………………….Screw
RBM076-1………………………………………….Panel screw (longer)
RBM076-2………………………………………….Button head screw (2pcs)
RBM076-3………………………………………….Screw (2pcs)
RBM076C………………………………………….Lockwasher
RBM076D………………………………………….Washer
RBM076E………………………………………….Nut
RBM076F………………………………………….Washer
RBM077………………………………………….screw
RBM077C………………………………………….Lockwasher
RBM077D………………………………………….Washer
RBM077B………………………………………….Lockwasher (2pcs)
RBM078………………………………………….Flathead screw
RBM079………………………………………….Cable clamp (4pcs)
RBM079B………………………………………….Cable Clamp 1pc
RBM080………………………………………….Switch stop block
RBM081………………………………………….Door Latch
RBM082………………………………………….Screw (3pcs)
RBM083………………………………………….Latching block
RBM083A………………………………………….Screw (2pcs)
RBM083B………………………………………….Lockwasher (2pcs)
RBM090………………………………………….Plate
RBM090A………………………………………….Screw
RBM090B………………………………………….Foot
RBM090C………………………………………….Nut
RBM090D………………………………………….Lockwasher
RBM090E………………………………………….Screw
RBM090F………………………………………….Lockwasher
RBM090G………………………………………….Washer
RBM091………………………………………….Window frame bar (4pcs)
RBM091A………………………………………….Window
RBM091B………………………………………….Screw
RBM091C………………………………………….Lockwasher
Control Panel Parts List
RBM081…………………………………………………………Timer
RBM082…………………………………………………………Frequency Drive (Speed controller)
RBM082B…………………………………………………………Spacer (4pcs)
RBM083…………………………………………………………Relay
RBM084…………………………………………………………Connector
RBM085…………………………………………………………Connector
RBM115…………………………………………………………Terminal Block
RBM115A…………………………………………………………Terminal Block
RBM116…………………………………………………………Terminal Block
RBM116A…………………………………………………………Terminal End (2pcs)
RBM117…………………………………………………………Fuse and Fuse Holder
RBM117B…………………………………………………………2A Fuses
RBM119…………………………………………………………Start button
RBM119A…………………………………………………………Emergency Stop
RBM119B…………………………………………………………Stop Button
RBM121-1…………………………………………………………Control Box
RBM122…………………………………………………………Cable Can be purchased by the ft.
RBM123…………………………………………………………Cable Can be purchased by the ft.

Speed Control Chart

Control Display Number (Hz)

Rodmill Revolutions Per Minute (rpm)

10

15

15

23

20

30

25

38

30

45

35

53

40

60

45

68

50

75

55

83

60

90